{"id":4367,"date":"2019-06-20T15:39:28","date_gmt":"2019-06-20T15:39:28","guid":{"rendered":"https:\/\/charcoalmachines.com\/?p=4367"},"modified":"2024-03-29T16:26:10","modified_gmt":"2024-03-29T08:26:10","slug":"how-to-make-charcoal-with-the-airflow-hoisting-carbonization-furnace-step-by-step","status":"publish","type":"info","link":"https:\/\/charcoalmachines.com\/de\/how-to-make-charcoal-with-the-airflow-hoisting-carbonization-furnace-step-by-step\/","title":{"rendered":"Wie man Schritt f\u00fcr Schritt Holzkohle mit dem Luftstrom-Hebeverfahren herstellt?"},"content":{"rendered":"

The airflow hoisting carbonization furnace is composed of the movable outer stove, inner stove, airflow pipes, ignition port, hoisting equipment, and the flue gas purification equipment<\/b><\/strong><\/a>. The inner stove is independent so that the charcoal furnace can be a single inner stove, three inner stoves, and four inner stoves. The carbonization inner stoves are connected by pipes, and the combustible gas in the carbonization process<\/b><\/strong> can burn each inner furnace which has high working efficiency and can save fuel consumption.<\/p>\n\n\n\n

\"Luftstrom-Hebeverfahren\"
Luftstrom-Hebeverfahren 1<\/figcaption><\/figure>\n\n\n\n

Die Details des Prozesses zur Herstellung von Holzkohle durch die <\/b><\/strong>Luftstrom-Aufzieh-Ofen zur Verkohlung<\/b><\/strong>:<\/b><\/strong><\/h2>\n\n\n\n

Stufe 1: Trocknungsprozess<\/h3>\n\n\n\n

After placing the inner stove which is of the biomass rods in the Holzkohle <\/b><\/strong>furnace<\/b><\/strong>, to ignite at the ignition port below the furnace, and the temperature in the furnace is gradually heated from normal temperature to about 100 \u00b0C. Because the temperature inside the furnace before ignition is low, this process should be heated with a large fire, reaching 100 degrees to the left, and then use a small fire to heat the carbonization<\/b><\/strong> temperature<\/b><\/strong> to 170 \u00b0 C – 200 \u00b0 C or so.<\/p>\n\n\n\n

Stufe 2: Pyrolyseprozess<\/h3>\n\n\n\n

When the temperature in the carbonization furnace reaches 170 \u00b0 C – 200 \u00b0 C, use a simmer to heat the furnace temperature to about 340 \u00b0 C. The second phase takes about 2 hours and 30 minutes.<\/p>\n\n\n\n

\"Luftstrom-Aufzieh-Ofen
Luftstrom-Hebeverfahren 2<\/figcaption><\/figure>\n\n\n\n

Stufe 3: schnelles Pyrolyseverfahren<\/h3>\n\n\n\n

When the temperature in the furnace reaches about 340 \u00b0C, use a small fire to heat the furnace temperature<\/b><\/strong><\/a> from 340 \u00b0C to 380 \u00b0C – 400 \u00b0C. The third phase takes about 2 hours.<\/p>\n\n\n\n

Stufe 4: das Ende der Verkohlung<\/h3>\n\n\n\n

Wenn die Temperatur im Ofen etwa 400 \u00b0C erreicht hat, \u00e4ndert sich danach nichts Wesentliches mehr. Mit einem kleinen Feuer wird weiter erhitzt, wenn die Rauchabgabe am Rauchabzug deutlich reduziert und leichter wird, wird die Flamme gel\u00f6scht und die Verkohlung ist beendet. Die vierte Phase dauert etwa 40 Minuten.<\/p>\n\n\n\n

Stufe 5: Abk\u00fchlung und Entladung des Holzes<\/h3>\n\n\n\n
\n\n<\/figure>\n\n\n\n

After the carbonization is completed, if no other cooling measures are taken, the fire can be sealed and the charcoal can be naturally cooled. There are two ways to seal fires: Method 1: seal the smoke outlet and cool the charcoal, and the surface of the Holzkohlebriketts<\/b><\/strong><\/a> is good. This method takes about 16 hours to cool down the charcoal. Method 2: completely open the smoke outlet and cool the charcoal. This process is the same as method 1, but the charcoal surface is not shiny like the former. This method takes about 16 hours for cooling. In these two ways, when the temperature in the furnace drops to about 40\u00b0C, to discharge the charcoal is ideal.<\/p>\n\n\n\n

Holzkohleproduktionsausr\u00fcstung zum Verkauf<\/strong><\/h2>\n\n\n\n
\"Holzkohlebriketts1\"
Holzkohlebriketts1<\/figcaption><\/figure>\n\n\n\n

Note: If there is no temperature measuring device or temperature measuring device damaged in the Luftstrom-Aufzieh-Ofen zur Verkohlung<\/a><\/b><\/strong>, the small-fire firing in the carbonization process shall take 7-8 hours. It is strictly forbidden to use a large fire during the carbonization process. At the end of carbonization, when the amount of smoke from the outlet is significantly reduced and the smoke is light, the flame should be extinguished and the carbonization is over.<\/p>","protected":false},"excerpt":{"rendered":"

The airflow hoisting carbonization furnace is composed of the movable outer stove, inner stove, airflow pipes, ignition port, hoisting equipment, and the flue gas purification equipment. The inner stove is independent so that the charcoal furnace can be a single inner stove, three inner stoves, and four inner stoves. The carbonization inner stoves are connected […]<\/p>\n","protected":false},"author":1,"featured_media":4369,"parent":0,"comment_status":"open","ping_status":"open","template":"","meta":{"wpai_generated_summary":""},"tags":[23,6,52],"info-type":[2],"class_list":["post-4367","info","type-info","status-publish","has-post-thumbnail","hentry","tag-carbonization-furnace","tag-charcoal-machine","tag-charcoal-making-machine","info-type-faq"],"_links":{"self":[{"href":"https:\/\/charcoalmachines.com\/de\/wp-json\/wp\/v2\/info\/4367","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/charcoalmachines.com\/de\/wp-json\/wp\/v2\/info"}],"about":[{"href":"https:\/\/charcoalmachines.com\/de\/wp-json\/wp\/v2\/types\/info"}],"author":[{"embeddable":true,"href":"https:\/\/charcoalmachines.com\/de\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/charcoalmachines.com\/de\/wp-json\/wp\/v2\/comments?post=4367"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/charcoalmachines.com\/de\/wp-json\/wp\/v2\/media\/4369"}],"wp:attachment":[{"href":"https:\/\/charcoalmachines.com\/de\/wp-json\/wp\/v2\/media?parent=4367"}],"wp:term":[{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/charcoalmachines.com\/de\/wp-json\/wp\/v2\/tags?post=4367"},{"taxonomy":"info-type","embeddable":true,"href":"https:\/\/charcoalmachines.com\/de\/wp-json\/wp\/v2\/info-type?post=4367"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}